As I was pondering the next step with my bag of 2SC5707 transistors the problem of heat-sinking occurred to me. An elegant solution would be to mount the transistors to the PCB but the cooling is awkward. Then I remembered how effective forced air cooling is and remembered I hadn't shared this with readers before.
I put most commercial class VHF FM transceivers way ahead of ham gear when it comes to selectivity and immunity from pagers. The only drawback I have ever noticed was with regard to transmitting duty cycle. Generally, the commercial transceiver was never intended for long overs and the heat-sinking reflects this. Fine for repeater use but if you have a long over on simplex things get hot. Sometimes very hot!
Here is a simple project that really protects that radio. First, the results of before and after measurement of heat-sink temperatures are shown below on a Philips PRM80 transmitting 25 watts into a dummy load:
It is true that many transmissions do not last 3 minutes or longer. However, a high SWR at the radio will increase the heat dissipated by the final transistor. I generally only check my antenna when I suspect it needs to be checked. So I could be transmitting for some time before any problem is detected. And while I have never sat on the microphone I am sure we have all heard someone driving around with the transmitter keyed up for extended periods.
I consider this a worthwhile addition to any PMR type radio. From the circuit below you will see that when the output of the temperature sensor reaches a set point the fan is turned on. Once the temperature falls the fan turns off.
I made mine on a small 0.8mm thick piece of PCB so that the surface mount LM61 could be mounted in a slot in the board to make contact with the heat-sink when the pcb was bolted to the heat-sink.
I'm going to use the same circuit on a forthcoming experimental HF amplifier using all of my remaining 2SC5707's. One last hurrah for them or a successful 15 watt linear amplifier for the lower HF bands.
Regards
Richard VK6TT
A blog about homebrew projects for Ham Radio. I cover aerials, test equipment, transmitters, both QRP and QRO, receivers and transceivers. The emphasis is on design and building. Generally I have boards and parts available at a modest cost. If you need more details, like a board layout, or any questions please ask. I'm more than happy to help.
Friday, 5 May 2017
Friday, 28 April 2017
Test Equipment Tip for Initial Testing of Transmitter Amplifiers
While many of us start out building transmitter stages and tuning for maximum output, we should quickly learn that over-driving a transmitter stage must be avoided. Even a slightly over driven amplifier stage generates significant harmonics and distortion products. So here is a quick tip on using the oscilloscope to check for the presence of a transmitter stage being over-driven.
A 10MHz analogue oscilloscope will be fine for looking at HF signals since we are going to measure relative voltages. I am unsure if a low bandwidth digital CRO will work.
Connect your oscilloscope to the collector or drain of the active device. With no drive and the oscilloscope set to AC coupling ensure the horizontal trace is on the centre graticule. The time-base setting is not critical so I use something that gives me a band across the screen with drive applied rather than the actual waveform. Try 1ms per division and adjust to suit your preference.
Now apply perhaps 10% of the drive you expect to use when the amplifier is in operation. Adjust the trace so it sits between say the second graticule above the centre line and the second graticule below the centre line. As you increase the drive you should see the trace touch the third graticule above and below the centre line at the same time.
Adjust the vertical amplifier gain to reduce the signal size on the screen then increases the drive again. Again, you should see the trace touch the third graticule above and below the centre line at the same time. Keep repeating this until you notice that one of the third graticule's above or below the centre is being touched before the other is being touched.
At this point the amplifier is no longer linear. If you have a fast oscilloscope you can increase the time-base speed to observe a few cycles of the waveform. You will notice that when non-linear the waveform peaks that were last to hit the third graticule will be distorted.
You can back off the drive until both the positive and negative peaks are moving in unison, which I find easier to discern with a slow timebase setting rather than a few cycles being displayed on the screen. That is the limit for linear operation of the stage.
Spectrum analysers and other nice test gear allow you to measure how non-linear your transmitter is. But isn't it easier just to avoid over-driving the transmitter to begin with? Hopefully this tip helps you avoid over-driving your transmitter stage giving you a nice clean signal when you finally go on air.
Regards
Richard VK6TT
A 10MHz analogue oscilloscope will be fine for looking at HF signals since we are going to measure relative voltages. I am unsure if a low bandwidth digital CRO will work.
Connect your oscilloscope to the collector or drain of the active device. With no drive and the oscilloscope set to AC coupling ensure the horizontal trace is on the centre graticule. The time-base setting is not critical so I use something that gives me a band across the screen with drive applied rather than the actual waveform. Try 1ms per division and adjust to suit your preference.
Now apply perhaps 10% of the drive you expect to use when the amplifier is in operation. Adjust the trace so it sits between say the second graticule above the centre line and the second graticule below the centre line. As you increase the drive you should see the trace touch the third graticule above and below the centre line at the same time.
Adjust the vertical amplifier gain to reduce the signal size on the screen then increases the drive again. Again, you should see the trace touch the third graticule above and below the centre line at the same time. Keep repeating this until you notice that one of the third graticule's above or below the centre is being touched before the other is being touched.
At this point the amplifier is no longer linear. If you have a fast oscilloscope you can increase the time-base speed to observe a few cycles of the waveform. You will notice that when non-linear the waveform peaks that were last to hit the third graticule will be distorted.
You can back off the drive until both the positive and negative peaks are moving in unison, which I find easier to discern with a slow timebase setting rather than a few cycles being displayed on the screen. That is the limit for linear operation of the stage.
Spectrum analysers and other nice test gear allow you to measure how non-linear your transmitter is. But isn't it easier just to avoid over-driving the transmitter to begin with? Hopefully this tip helps you avoid over-driving your transmitter stage giving you a nice clean signal when you finally go on air.
Regards
Richard VK6TT
Tuesday, 25 April 2017
250mW Class A Amplifier with 2SC5707
Further to my recent posts on using the 2SC5707 of unknown origin I finally got around to some more testing. I calculated the component values for a 250mW Class A amp and after etching a circuit board built the amplifier for testing. Overall, the results were pleasing and justify further experimentation.
Referring to my bible, "Solid State Design" by Hayward and DeMaw, I expected a gain of 17dB from the circuit below:
I achieved this 17dB of gain at 10MHz. However, the gain had fallen by 4dB at 20MHz so at present I will limit my use of this transistor to 14MHz and lower.
My clip on heatsink was a 15mm x 15mm piece of circuit board, held on with a wooden clothes peg. Worked extremely well for testing but I have a more permanent solution in mind which I will post about shortly.
Overall a nice little amplifier and I will box it up for use on the workbench to increase the drive from my signal generator as required. But ironical that it will be a 15c transistor between two expensive BNC connectors.
With 8 transistors left I will really push them in the next experiment to see if there is any smoke in them!
Referring to my bible, "Solid State Design" by Hayward and DeMaw, I expected a gain of 17dB from the circuit below:
I achieved this 17dB of gain at 10MHz. However, the gain had fallen by 4dB at 20MHz so at present I will limit my use of this transistor to 14MHz and lower.
My clip on heatsink was a 15mm x 15mm piece of circuit board, held on with a wooden clothes peg. Worked extremely well for testing but I have a more permanent solution in mind which I will post about shortly.
Overall a nice little amplifier and I will box it up for use on the workbench to increase the drive from my signal generator as required. But ironical that it will be a 15c transistor between two expensive BNC connectors.
With 8 transistors left I will really push them in the next experiment to see if there is any smoke in them!
Subscribe to:
Posts (Atom)

