OK, so I saw a blog post by someone who suggested they were getting a batch of boards done at a great price. I won't name them because their bargain was way too expensive once freight was included. But by the time I discovered that it was too late, I'd made the mental commitment to one final, best I could build version.
Since then I've sat on my hands for almost a year. But this weekend I needed a break from the maths of loop filters and modifying 10GHz equipment. I wanted something I could do without much thought. And since all the planning for this was done around a year ago it seemed like it was time to start.
I had wanted to see if toroids would offer a significant advantage over the tuned inductors in the RF bandpass filter. While the existing filter works really well, I considered moving from adjustable inductors, with a Q of perhaps 70, to toroids with a Q of say 200.
The tighter filter passband became less attractive when I worked out the maximum inductance I could wind on the toroids was around 1uH. A larger inductor has wire too fine to allow for compression and expansion of the coil turns to tune the filter. The advantages of the higher Q are offset by the lower impedances within the filter and the net result is not much difference. Had I had a larger toroid then things would have been different. So I will stick with the existing filter and this iteration will really be about incorporating all the modifications I made on the fly.
Here is a piece of advice I agonised over putting to print. I'm not comfortable denigrating other people's designs. But I was gob-smacked to see someone recommend an AM broadcast filter for a 40m receiver as a way of fixing receiver overload from short-wave transmitters. I'd like to know how that works. Because I can see no way that it can work. Remember, AM broadcast signals are around 1MHz. Those pesky short-wave signals run from 40m upwards to perhaps 16MHz.
And another matter that galls me is people still promoting simplistic designs as being worthwhile. If the project doesn't have at least a double tuned band pass filter between the aerial and first mixer then it's a glorified crystal set. I do wonder if those that propose the "easy" way know what they are doing. For all the effort that goes into building a receiver reward yourself many times over with another 1% of effort and put in two or three extra components in one of the most critical parts of your receiver.
Here's a picture of progress to date. I hope to have this finished by the end of the month. Then I'll think about what to do with all the spare boards. Any takers??
Regards
Richard VK6TT
A blog about homebrew projects for Ham Radio. I cover aerials, test equipment, transmitters, both QRP and QRO, receivers and transceivers. The emphasis is on design and building. Generally I have boards and parts available at a modest cost. If you need more details, like a board layout, or any questions please ask. I'm more than happy to help.
Monday, 19 February 2018
Monday, 12 February 2018
EM 10.5-10.68GHz microwave modules - Mods to use on 10.368GHz - update
The first RX module which down converts 10GHz to 144MHZ was finally finished today. Initial results were disappointing. However, after some modifications to improve the noise characteristics of the first local oscillator everything is running nicely now.
The conversion takes a while but the result is a sensitive down converter suitable for SSB and FM use. I'm not posting full details of all the changes required at this point. Please get in touch if you'd like to know more and I'll consider blogging further details.
In the meantime I have a few more modules to convert. The RX module has the following model identifiers:
em FM RECEIVER
10.5-10.68 GHz, Synth
P/N 036D S/N 111xxx
The conversion takes a while but the result is a sensitive down converter suitable for SSB and FM use. I'm not posting full details of all the changes required at this point. Please get in touch if you'd like to know more and I'll consider blogging further details.
In the meantime I have a few more modules to convert. The RX module has the following model identifiers:
em FM RECEIVER
10.5-10.68 GHz, Synth
P/N 036D S/N 111xxx
Wednesday, 17 January 2018
EM 10.5-10.68GHz microwave modules - Mods to use on 10.368GHz
This started out as what appeared to be an ambitious project but it is so far straightforward. I was fortunate enough to be given the chance to modify a few sets of the FM Tx and Rx boxes for ham use. It transpires that just about every set of modules is the same but different! They are all broadly similar but subtle variations exist so if you have some of these modules and yours don't match exactly then this shouldn't deter you.
Here's what I have done so far:
The units I modified had the LM2326 PLL chip. It has a different data format than the LM2325 chip I saw on the units I have not yet modified. In a few words the 2.5GHz PLL uses a 250KHz reference frequency. It is multiplied by 4 on both tx and rx units. On the tx units it is mixed with the IF, presently 69MHz but I am modifying this to use a 144MHz IF on tx. On Rx the multiplied signal is mixed with a 692MHz oscillator down to a 140MHz IF. At present I'm leaving this oscillator alone since the saw filter appears wide enough to be serviceable with a 2m IF.
Micro
Once I knew what the existing data stream was it was relatively simple to work out the data stream needed to load the PLL chip with data to put it on the desired frequency. See the chart below for an overview. I used an ATTINY13 and a few lines of assembly to do this.
Achieving lock.
This should be straightforward but sometimes the soldering proves difficult due to the heatsinking the board has. I moved the short until the PLL locked with around 4V-6V on the tuning voltage link.
I'll post some more pics soon but for now the following may prove useful.
Regards
Richard
Here's what I have done so far:
- Used a cheap logic analyser to check what was being loaded into the PLL chip by the micro.
- Inserted my own micro to control the 2.5GHz PLL
- Achieved lock on several TX and RX units
The units I modified had the LM2326 PLL chip. It has a different data format than the LM2325 chip I saw on the units I have not yet modified. In a few words the 2.5GHz PLL uses a 250KHz reference frequency. It is multiplied by 4 on both tx and rx units. On the tx units it is mixed with the IF, presently 69MHz but I am modifying this to use a 144MHz IF on tx. On Rx the multiplied signal is mixed with a 692MHz oscillator down to a 140MHz IF. At present I'm leaving this oscillator alone since the saw filter appears wide enough to be serviceable with a 2m IF.
Micro
Once I knew what the existing data stream was it was relatively simple to work out the data stream needed to load the PLL chip with data to put it on the desired frequency. See the chart below for an overview. I used an ATTINY13 and a few lines of assembly to do this.
Achieving lock.
This should be straightforward but sometimes the soldering proves difficult due to the heatsinking the board has. I moved the short until the PLL locked with around 4V-6V on the tuning voltage link.
I'll post some more pics soon but for now the following may prove useful.
Regards
Richard
![]() |
| An unmodified receiver showing what is required to modify for 10.368GHz use |
| Details of how the IF signal on Tx gets to the mixer diode for up-conversion to 10GHz |
![]() |
| Data loaded into PLL chips to shift to 10.368GHz |
Subscribe to:
Posts (Atom)


