Pages

Tuesday, 12 October 2021

Voltage Regulation - Distributed or Lumped?

I'm getting tired of the semiconductor supply disruptions which manifests itself as price increases and supply shortages. Even humble voltage regulation is being impacted.

As an example of the voltage regulation quandary consider the synthesizer board in my present project, a HF SSB transceiver based on the Weaver method.  In the past I would have slapped a 7805 linear regulator on the chassis for heat-sinking and used wires to connect it to the PCB. But this project is being designed with modular PCB's sized 100mm x 33mm since this fits into a readily available extruded aluminium tube. So less wiring from the chassis to pcb's inside tubing is better.

An AD9850 based synthesizer with micro, mmic and switchable outputs draws some 150-180mA. Now I can use a 7805 type linear regulator in a TO-252 (DPak) package but I have run out and the replacement will cost around $1. It could have cost as little as $0.30 but the wholesaler is out of stock. 

However, I could use 3 separate regulators on the board and that would cost around $0.15-$0.20. But my choices are much wider and the heat to be dissipated is spread over 3 regulators. My parts bin probably means I wont have to buy any regulators, a good thing, if I go down the distributed path.

Will normal ever return? After 12 months of the supply disruptions I am starting to wonder.

73's

IC-R8500 Repair

Was glad to help a good friend, VK6UM Larry, with the repair of an IC-R8500 recently. After some digging around it was clear this was a later version than the schematics I could find online applied to. The fault was the blinking display, a characteristic of a PLL not locking up. 

A few minutes with my ICQ7A used as a sniffer confirmed VCO_A had no output. A few voltage measurements and it appeared the special Icom chip, IC3, was not enabling the power to the VCO. Knowing that chip was likely to be unobtainable, and for thoroughness, I checked the main micro was sending instructions to the synthesizer board. 

I was able to confirm both shift registers, 4094's, were receiving pulses. But the shift register feeding the special Icom chip had no signals on the output pins that drive pins labelled "CON0" through "CON3". It seemed a reasonable assumption that these pins mapped to the output pins enabling the VCO's. So a replacement shift register was obtained.

Upon installation there was no change. A closer examination showed the data pulse was too low in amplitude to be considered a logic high. It transpired, after a fair amount of thought and measurement, that the data line was being loaded by a 130 ohm resistance that should not have been there. The fault was traced to a capacitor array on the main board having broken down somehow. Once removed from the PCB no amount of cleaning the defective part could remove this unwanted resistance, though it did change in value. 

A replacement part could not be found. So in desperation something was fabricated in-situ with 1206 22pF caps and fine wire. Partial success. The radio is now working within narrow segments of it's wideband coverage.

Saturday, 10 July 2021

IC-7000 and the 10 Ohm Thin Film Resistor Fix for Instability


I had a request from VK6EH recently for a 10 ohm "thin film" resistor to allow him to make this modification to his radio. After discussing the pro's and cons of thin film resistors and standard surface mount resistors we concluded a "thin film" part was not going to be any different from DC to 430 MHz when used in series with the gate. I don't know where this recipe originated but it reminds me why everything you read has to be treated with scepticism. Peer review is not the same as something is just repeated ad nauseam.

I can't recollect seeing a datasheet for a surface moiunt resostir that wasn't a film construction.So how bad is a standard off the shelf 10 ohm 1206 resistor with regard to parasitics? Since 1nH has 1ohm of reactance at 160-MHz (that's how I deal with stuff in my head), at 430MHz 1ohm of reactance requires around 400nH. (F increased say 2.5 times, so inductance divided by 2.5).

I measured an ordinary 10 ohm 1206 resistor:

 

I can't see how the small parasitics present in a 1206 resistor would make any difference at 430MHz. At HF they parasitics are truly small.. I don't have any 0805 or 0603 size10 ohm  parts to compare this with but I suspect they are even better with regard to parasitics. 

 I'm calling the need for a special thin film resistor busted. And looking at some of the information on the web about these failures is like reading tea leaves and hearing mumbo jumbo. 

The PD55015 is a very rugged part. I dragged the S parameters into RFSim and immedialtely saw that at 50MHz it is potentially unstable. However, the 10 ohm resistor is only a marginal improvement. It might be enough given the radio's remaining circuitry was excluded from the analysis.If I was doing this I'd tend towards 22 ohms and any SMD part that fitted.

73's